The construction of the wall is very simple, so the acceptance of the wall works is not complicated, as long as we have some expertise, a little closer look can get real results. The following is the knowledge and details of the paint project acceptance collected by Xiaobian for the majority of owners, I hope to be helpful to everyone. First, the paint construction process 1, paint must use high-quality paint. During construction, clean the site, minimize personnel activities and dusty processes. 2, check the cleaning of the base layer, you can use 400# sandpaper to gently polish the surface burrs, clean with a clean towel, check the surface of the panel for smudging, damage can be used. 3, all panels and lines should be used after making a transparent putty and a primer. After the substrate is cleaned, the transparent putty can be brushed or directly scraped according to the type of the panel. The transparent putty is sprayed twice, and after 4 hours of drying, the putty is thin and uniform. 4. After the putty is polished, the ratio of the transparent primer, the transparent primer and the clear transparent bottom to the curing agent and the diluent is 1:0.3:0.8～1. The transparent primer is filtered or sprayed with a 200# filter before use, and brushed twice. After 4 hours of drying, use 400# sandpaper to polish and clean. 5. After the putty is polished, the ratio of the transparent primer, the transparent primer and the clear transparent bottom to the curing agent and the diluent is 1:0.3:0.8～1. The transparent primer is filtered or sprayed with a 200# filter before use, and brushed twice. After 4 hours of drying, use 400# sandpaper to polish and clean. 6. When using the spraying process, the site should be cleaned, and the ground should be sprayed with a small amount of dust and sprayed evenly. Second, the acceptance method of ordinary paint 1. Whether the surface of the furniture blended oil is flat and saturated. Make sure that there are no blistering, no cracks, and that the paint is to be balanced in thickness and consistent in color. 2, the surface of the furniture varnish is consistent in thickness, the paint surface is saturated, clean, no particles. 3. Whether the surface latex paint has a smooth surface and uniform reflection, and there is no empty drum, foaming or cracking. 4, wood and gypsum board ceiling paint is generally latex paint, the surface should be flat, there is no crack at the board joint. 5. Whether the ceiling line connection is handled smoothly, there is no obvious deviation and deformation. 6, wallpaper patchwork is inaccurate, no tearing phenomenon. Patterned texture stencils should be accurate and error-free. 7. Whether the wall is free from contamination or dirt. Third, the adoption of wallpaper construction acceptance method First of all, we must use a professional paving team. They will have professional tools such as computer gluing machines, various types of brush rollers, etc. (Many of the tools used by domestic professional teams are imported from Japan), and when they are laid, wallpaper brushes After putting the wallpaper glue on it, let the wallpaper fully absorb the glue, then put it on the wall and use professional tools to make the wallpaper and the wall fit. In addition, the room with the wallpaper must be closed for two or three days, so that the wallpaper and the wall fit perfectly. The wallpaper can't be closed at the corner of the corner, and the wallpaper with the corner of the corner is easily scraped. The flower wallpaper must be affixed to the flower, otherwise it will look very messy. If you have a wallpaper with a flash on the flower, you can overlap the adjacent wallpaper and cut the edge with a sharp wallpaper knife. 1. The wallpaper is firmly pasted and the surface color is the same. There must be no bubbles, empty drums, cracks, curled edges, wrinkles and stains. There is no glue marks when squinting. 2, the surface is flat, no ripples and undulations. The wallpaper is connected to the hanging mirror line, the veneer and the baseboard. There must be no gaps. 3, each piece of splicing should be horizontal and vertical, the pattern of the splicing, pattern matching, no separation, no overlap, 1.5 meters from the wall face up, no seams. 4, the yin and yang corners are vertical, the edges and corners are distinct, the yin corners are spliced ​​with smooth light, and there are no seams at the male corners. 5, the edge of the wallpaper is straight and tidy, there must be no paper hair, flying thorns. 6, there must be no defects such as leakage and delamination. 7. All switch socket panels should be as shown in the photo, leaving the holes correctly. Fourth, the acceptance method of latex construction If you use latex paint to decorate the wall, there are still some ways to make the latex paint more expressive: 1. Treat the putty: Make the putty into a variety of texture lines such as hair, waves, mess, etc., and then brush the latex paint. 2. Treatment of latex paint: After brushing the latex paint, use a special patterned roller to make a pattern on the paint surface. 3. On the surface of latex paint: After the latex paint is finished, draw some patterns on the surface of the paint film. You can use hand-painted, or you can use some molds to print, you can also use stickers to shape, there are many ways. 4, in the grassroots treatment: after the completion of the putty construction, you can paste some painted wall coverings with texture, and then paint on it, and finally the effect is not bad. 5. The materials and colors used in the latex paint application meet the design requirements. 6. The color of the painted surface is the same, no blisters, no brush lines, and no quality defects such as through the ground, leaking brush, falling powder, skin alkali, peeling and biting. 7. When spraying with a spray gun, the spray point is even and even, no skin phenomenon is allowed, no flow is allowed, the hand touch paint film is smooth, no powder is removed, doors and windows, lamps, furniture, etc. are clean, no paint marks. 8, not allowed to drop powder, peeling, missing brush, through the bottom, bite the bottom, sag, sputum, brush marks and other phenomena. 9. The side view is flat and has no wavy shape. If the wall surface is repaired, the whole wall should be brushed. 3 Way Ball Valve,Three Way Ball Valve,3 Way Flanged Ball Valve,3 Way Electric Ball Valve Wenzhou Dico Valve Technology Co.,Ltd. , https://www.dicovalves.com
Home improvement wall engineering acceptance method