Bearing wall can not be removed For the renovation of old kitchens, the wall surface is often the key project. The old sand ash wall is prone to aging, causing the wall to crack. If the wall surface is better during the decoration, the patch can be cracked. If it involves the dismantling of the kitchen wall, first of all, it is necessary to know whether the kitchen wall is a light-weight wall, and then dismantle it after the property company agrees; if the wall is a load-bearing wall, it cannot be demolished. Tip: Generally, when decorating the old kitchen, do not easily remove the wall. First, the problem of kitchen fumes is not easy to solve. Second, the dust is very large when dismantled, and the indoor air is susceptible to pollution. If the house is too small, you can move the restaurant to the kitchen. Cast iron pipe changed to PPR pipe The kitchen has water pipes, natural gas, heating pipes, etc., which can cause leakage and pollution if accidentally. The pipes of the old houses are generally cast iron pipes or galvanized pipes, which are prone to rust, and there may be problems such as water leakage and running water of the heating pipes. When the refurbishment, the indoor water pipe can be changed to a PPR pipe. If the house is newer, the pipeline will also have to be checked for leaks. Tip: The water flow in the old kitchen is particularly bad, because the time is long, the filter on the side of the water meter blocks a lot of rust and dirt in the tap water. So find the decoration worker to remove the water meter and clean the filter. Single-channel water supply changed to two-way water supply Waterproofing is a problem that must be considered when the kitchen is remodeled. Some old houses have been waterproofed, but after several years and ten years, it may be waterproof. If you do not pay attention when removing the floor tiles, it may damage the waterproof, so you can avoid it. Check for water damage before the water test. If the waterproof is damaged, it must be re-waterproof before remodeling the kitchen. Today's buildings are generally two-way water supply. The kitchen in the old building is usually a one-way water supply, so it is best to add a hot water pipe when the kitchen is renovated. If the washing machine must be placed in the kitchen, an additional water pipe must be connected. Tip: Due to structural restrictions, water changes can only be changed to water, and water cannot be changed. The sundries can be found in the overall cabinet. Minimize the connector When the circuit is refurbished, the safety of electricity should be placed in the first place. Find the water circuit diagram of the original kitchen renovation, which makes it easier to retrofit the current hydropower line. For the wires of the old house, it must be replaced with national standard wires, and PVC insulated pipes must be worn when embedding the wires in the wall. The line should be as small as possible to reduce the joint. If it is necessary to connect the wiring, the joint line should be well-sealed and insulated and protected from moisture. The circuit layout of the old kitchen has many weaknesses. It is difficult for the strong electricity to meet the electricity demand of modern households. The weak electricity is also basically not in place. The aluminum core wires and the wires with small diameters in the circuit are all eliminated. Tip: In the circuit transformation, if the original line can be retained if it meets the standard, the new socket and lighting circuit should be separately routed from the distribution box. Any wiring or adding power to the socket and lighting on the original circuit will cause the single circuit to be overloaded. It is easy to cause a trip or burn out the main gate of the power supply and even cause a fire. ■Design Shelf instead of wall cabinet The old kitchen is particularly important because of the small space. The whole cabinet is an important piece of furniture for storage. Therefore, we must pay attention to the selection of the whole cabinet. The finished cabinet should be designed according to its height, cooking habits and safety. The dishes, cutlery, pots and sundries can be used. Find the location of the storage in the whole cabinet. The cabinet cabinet can also be “simplified†as a shelf. The use of the shelf does not reduce the storage function of the cabinet, which can make the kitchen look more transparent, but choose a material that is resistant to oily smoke and easy to scrub, otherwise it will take a long time. A layer of soot. Note: In the cabinet design, the material around the stove is made of fireproof material. The cutlery is preferably placed in a closed position and stored in a cabinet. The old kitchen has a flat or L-shaped layout that is more open. Cabinet manufacturers measuring size Old kitchen renovation, usually will be customized new cabinets, in addition to consider the quality of the cabinet and the overall layout of the kitchen is reasonable, but also pay attention to the coordination between the cabinet manufacturers and the decoration company. Usually before the kitchen is renovated, the cabinet manufacturer will go to the kitchen to measure. In addition to the size, it is necessary to see if the various pipes are suitable. If it is not suitable, it needs to be changed. Then the designer of the cabinet handed over a remodeling drawing to the decoration company for renovation. Cabinet doors are used more often, so you must choose good hardware to ensure a long time. Note: If the cabinet manufacturer does not have the quantity or the construction team does not strictly follow the size, there may be a situation where the interface is not right, and the manufacturer and the decoration company have a dispute and delay the construction period. Keep the lamps away from the stove The lights in the kitchen are damaged very quickly. The rust of the lamp in the kitchen and the poor contact are very common. Therefore, in the transformation, the design and installation of the lamp position should also be taken seriously. When installing the kitchen fixtures, the installation part should be as far as possible away from the stove, do not let the gas, water vapor directly dyed, the general device range hood or exhaust fan can solve this problem. The brightness of the luminaire must be sufficient, and the kitchen with too dim light will greatly reduce the quality of the food. Note: When replacing the kitchen light bulb, due to the long-term use, the corrosion is serious, the lamp holder and the lamp holder are rusted, and it is difficult to remove and replace. Therefore, when installing the bulb, a little Vaseline can be rust-proofed on the lamp cap. ■Demolition It takes thousands of dollars to dismantle the 5 square meter kitchen. The walls, floor tiles, doors and windows, and cabinets of the old kitchen are used all year round, and most of the owners will choose to remove them when they are renovating. At present, the cost of dismantling the old house of the home improvement company is generally charged in square meters. For a kitchen of about 5 square meters, the cost of light removal may be thousands of yuan. When removing the wall tiles, doors and windows of the old kitchen, you should pay attention to the concealed works such as waterways and circuits, especially the pipes and waterproof of the bathroom. Once damaged, the bathroom can easily seep into the downstairs. The transformation of special pipelines is to be carried out by gas companies. Many of them are not particularly old houses. The kitchen walls are mostly light-weight walls. Once the light-weight walls are broken, the repairs are very complicated and the walls are not as strong. If the old kitchen needs to keep the floor, cabinets, etc., it needs to be protected with professional materials when dismantling to avoid unnecessary losses. For kitchens that are not too old, in the second renovation, if there is not much problem in the original decoration in the kitchen, it can be properly reserved. The wall tiles can be retained without cracking or emptying; floor, ceiling, hanging cabinet, etc. If the protection is usually good, it can be reused after a little modification or decoration.
Resin Bond diamond and CBN Grinding Wheels
are made of either phenolic or polyimide resins. Pressure and heat are utilized
to bond the resin to our grinding wheel cores.
Resin bonded CBN Grinding Wheels are widely
used on CNC machine for all tyeps of high speed steel cutter and drills
machining and sharpening. They come mostly on shape of straight wheel of plat
wheel, or bow shape wheel, or the working part can be sharpened to special shape
like v shape or bevel shape.
A silicon carbide stone dresser is mostly
used for the diamond or CBN grinding wheels.
Kemei produces all types and shapes diamond
grinding wheels and CBN grinding wheels, and wheel dressers. If you need any grinding
solution, contact us.
Resin Bond Grinding Wheels,Resin Bonded Diamond Wheel,Resin Bond Cutting Wheel,Resin Bond Diamond Cutting Wheel Henan Jinlun Superhard Material Co., Ltd , https://www.jinlungrindingtools.com
Phenolic bonded wheels can be utilized in dry or wet applications. Our
polyimide bonded wheels are best utilized in water or oil-based coolants for
improved form holding, typically required in CNC tool and cutter applications.
The kitchen has a second renovation.