Bugle Head Auto Screws,Indented Hex Washer,Bugle Head Drywall Screws,Bugle Head Self Drilling Screws CANGZHOU LINGANG YUANFENG IMPORT & EXPORT TRADING CO.,LTD , https://www.clyfhardware.com
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131"; Home>Bearing knowledge>Smooth bearing Smooth bearing
First, the smooth bearing effect has a significant impact on the fatigue life of the rolling bearing and conflict, wear, temperature, oscillation, etc.; there is no normal smooth; the bearing can not work. Analyze the cause of bearing damage; 40% of the bearing damage Both are related to smoothness. Therefore, the outstanding smoothness of the bearing is a useful way to reduce bearing conflict and wear. In addition to this; the smoothness of the bearing and heat dissipation; rust, sealing, flat cushioning, etc.; The effect can be briefly stated as follows: /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
a. An oil film is formed between the two tumbling surfaces or the sliding outer surface that touch each other to separate the two outer surfaces; the collision and wear of the touch surface are reduced.
b. When the oil is smooth, especially when the circulating oil is smooth, the oil mist is smooth and the fuel injection is smooth; the smooth oil can take away most of the conflict heat inside the bearing; it has a useful heat dissipation effect.
c. When the grease is smooth, it can avoid foreign matter such as dust from entering the bearing;
d. Smoothing agents have the effect of avoiding metal corrosion. The fatigue life of the extended bearing.
Second, the smooth method of the grease smooth and oil smooth comparison bearing is roughly divided into two kinds of grease smooth and oil smooth. In order to give full play to the function of the bearing; the important thing is to use the reduction and application intention; select the smooth method. Table 4-2 Shows the advantages and disadvantages of smooth grease and smooth oil. Third, the smooth and smooth grease is a smoothing agent composed of base oil; thickener and additives. When selecting; should choose the grease that is very suitable for the bearing application conditions; because the trademark Not the same; there will be a lot of difference in function; so the time of selection; it is necessary to pay attention.
The smooth grease commonly used in bearings is calcium-based smooth fat, sodium-based smooth fat, calcium-sodium-based smooth fat, lithium-based smooth fat, aluminum-based smooth fat and molybdenum disulfide smooth grease.
The amount of smooth grease filled in the bearing; suitable for 1/2-1/3 of the inner space of the overflow bearing. It should be reduced to 1/3 at high speed. Excessive smooth grease will increase the temperature rise. 4. Selection of smooth grease When selecting smooth grease according to operating temperature; the primary target should be dropping point; oxidation stability and low temperature function; dropping point can usually be used to evaluate high temperature function; bearing practice temperature should be lower than dropping point 10-20 °C. The temperature should be below the dropping point of 20-30 ° C.
When selecting smooth grease according to bearing load; for heavy load, choose smooth grease with small penetration. When working under high pressure, except for small penetration; also have higher oil film strength and extreme pressure function.
When selecting smooth grease according to environmental conditions; calcium-based smooth fat is not easily soluble in water; suitable for dry and less watery environment. 5. Oil is smooth under high-speed and high-temperature conditions; when grease is not suitable, oil can be used smoothly. After smooth oil circulation; can take away a lot of heat. Viscosity is an important characteristic of smooth oil; the viscosity of the powder directly affects the fluidity of the smooth oil and the oil film thickness formed between the conflicting surfaces; the viscosity of the smooth oil at the bearing operating temperature is usually 12 -15cst. ​​The higher the speed, the lower the viscosity should be selected; the heavier the load should choose the higher viscosity. The commonly used smooth oils are mechanical oil, high-speed mechanical oil, turbine oil, compacting oil, transformer oil, cylinder oil, etc. :
a. Oil bath smooth oil bath smooth is the most common smooth method; suitable for the smoothness of low and medium speed bearings; part of the bearing is immersed in the groove; smooth oil is brought up by the rotating bearing parts; then it flows back to the oil groove. Below the middle of the lowest roll.
b. Drip oil smooth drip smooth is suitable for the quantitative supply of smooth oil bearing parts; the amount of oil is usually one drop every 3-8 seconds; too much oil will lead to increased bearing temperature.
c. The circulating oil is smooth and the oil is pumped to the bearing parts; the smooth oil after the bearing is filtered and cooled, and then used. Because the circulating oil can take away a certain amount of heat; the bearing is cooled; therefore, the method is suitable for bearings with higher speed. component.
d. The spray is smooth and mixed with smooth oil by a sprayer to form an oil mist; in the eruption bearing; the air flow can effectively cool the bearing and avoid the intrusion of impurities. This method is suitable for the smoothing of high-speed, high-temperature bearing components.
e. The illuminating and sliding oil pump pumps the high-pressure oil into the bearing through the nozzle; the oil injected into the bearing flows into the oil groove through the other end of the bearing. When the bearing rotates at a high speed; the rolling body and the cage also make the ambient air flow at a suitably high rotation speed. It is difficult to send the smooth oil to the bearing in a generally smooth manner; it is necessary to spray the smooth oil into the bearing by means of a high-pressure eruption; the nozzle should be placed between the inner ring and the middle of the cage.
Sixth, the solid is smooth under some special operating conditions; a small amount of solid smoothing agent is involved in the smooth grease; if you participate in 3 to 5% of the No. 1 molybdenum disulfide can reduce wear; improve the resistance to heat and heat; about high temperature, elegant, high Vacuum, corrosion resistance, radiation resistance; and special conditions such as extremely low temperature; solid smoothing agent to participate in engineering plastics or powder metallurgy materials; can be made into bearing parts with self-smooth function; It is knotted on the raceway, cage and rollover; it forms a smooth film; it has a certain effect on reducing conflict and wear.
Seven, the smoothing agent to make up and replace a. The smooth grease compensates for the interval because of the mechanical effect; the addition of aging and pollution; the smooth base filled in the bearing equipment will gradually lose its smooth function. Therefore, the smooth rank needs to be continuously compensated and updated. The composition, scale and rotational speed of the bearing are different. Figure 4-1 shows the approximate interval of smooth grease according to the working time requirement.
In the case of Figure 4-1; when the bearing temperature exceeds 70 ° C; the bearing temperature rises by 15 ° C; it is necessary to use the smooth grease to make up the interval to cut by half.
The double-sided closed bearing is now filled with grease at the time of manufacture; “HRB†uses the standard smooth grease in these products; the common working temperature scale and other functions are suitable for the regular occasion; and the grease filling amount also corresponds to the bearing size. The life of the grease can usually exceed the bearing life; except for special occasions; no need to make up for smooth grease.b. Smooth oil replacement cycle The replacement cycle of smooth oil is different depending on the application conditions and oil quantity; usually; when the working temperature is below 50 °C; when it is used in an excellent environment with less dust; once a year; when the oil temperature reaches At 100 ° C; replace it once every 3 months or less.
Recommend to friends comments close window Bearing related knowledge The clearance of the machine tool spindle and the bearing rolling bearing The preparation work before the bearing device The bearing equipment of the rolling bearing and the basic requirements of the component rolling bearing for the data function
This article links to http://
Please indicate the bearing network http://
Previous: Foreign mechanical occupation bearing heat disposal method (on)
Next: KOYO bearing application methods and matters needing attention
Smooth bearing
Source: China Bearing Network Time: 2013-04-03