Curvy Welded Mesh Panels,Weldmesh Sheets,Welded Mesh Panels,Welded Mesh Sheets ANPING HONGYU WIREMESH CO.,LTD , https://www.hongyufence.com
The system engineering of LCD splicing is divided into four phases: project planning, preliminary investigation, project implementation, and later stage of the project. Among them, the preliminary survey and project implementation are more important in the whole process. If any one of these two problems occurs, it will affect the progress and quality of the project. The preliminary investigation required that the project personnel should come to the site to understand the situation in person, communicate with the customer when necessary, carry out detailed communication, determine the overall construction plan, plan the entire project, and help improve the short construction cycle and the presentation of the final results. Professional 5-point LCD splicing installation common sense, then, to install LCD splicing to a few steps? Technical personnel are described as follows: 
1, the installation of the equipment to be leveled because the entire large-screen LCD splicing system is very large weight, its technology determines its cabinet is large, and heavy, so if the installation of equipment is the floor of the tile, we must first confirm whether it can To bear such a weight, the other equipment is best fixed on the ground under the anti-static floor to ensure that the ground will not be deformed due to heavy loads.
2. Wiring of the LCD large-screen splicing system requires separation of the power line and the signal line to avoid unnecessary interference with the signal. In addition, the required size of the LCD screen, the cabinet position, and the signal source position should be calculated. The length of the cable, the number of connectors, and the name of the signal cable. At the same time, we must confirm with the customer whether the pipeline channel available for the project meets the actual demand in order to continue the follow-up work.
3. Ambient light Because the brightness of LCD large-screen splicing products is relatively limited, if the surrounding light of the system is too bright, it will have a certain impact on the picture effect. Under normal circumstances, it requires a dark area within 4m in front of the screen. It is better not to install fluorescent tubes, to install a built-in downlight, and the light cannot directly shine on the screen and there must be a separate switch. In addition, the installation of the lamp tube should be parallel to the large-screen equipment, as much as possible to ensure that there is sufficient lighting in the work area, but it will not have a significant impact on the screen, the light (such as windows) may be injected near the screen, if necessary, to block At the same time, the light is best turned off when the equipment is running to ensure the normal operation of the equipment.
4, the framework requires taking into account the convenience of installation and maintenance, the framework must be detachable wrapping edge. In the outer frame, about 25 mm clearance is reserved on each side of the outer edge (up, down, left, and right sides) of the mosaic wall, and the large-scale fight wall should also be properly increased according to the number of columns. In addition, in order to enter the box after maintenance, maintenance access in principle is not less than 1.2m wide. The detachable edge strip is suitable for pressing down the edge of the screen by 3-5mm, and after the box body and the screen are fully mounted, the detachable edge strip is fixed finally.
5, air-conditioning In the maintenance of the channel, must be installed air-conditioning or outlet, ensure good ventilation equipment. The position of the air outlet should be as far away as possible from the projection wall (about 1m or so), and the air from the air outlet can not be directly blown against the box, so as to avoid damage to the screen due to uneven heating and cooling.
The above is a detailed introduction to the “Professional 5-Point LCD Splicing Installation Knowledge†and hopes to help everyone.
This article is from Weiding Technology
Professional 5 LCD splicing installation knowledge
Recently, many netizens have been consulting online for a problem, that is, how to install LCD panels. What are the common senses for installing LCD panels? Today, we asked Weiding experts and technicians to give you a detailed introduction. : The installation of the project is also a more complicated process. Each step of the installation is more important. A complete set of LCD splicing system, in addition to the front-end screen, also involves the computer, network, image monitoring, integrated wiring and many Peripheral equipment and many other devices. The liquid crystal splicing system project requires specialized technical personnel to operate, so that the entire project can be smoothly installed.