Tiles are more common decoration materials, because the tiles on the floor will make the visual effects and the use of effects are very good, so more and more families will buy tiles, but the tiles are also need to pay attention, different tiles The effects of the methods are different. Then, the next small series for everyone to introduce how to tile and tile selection methods. How to tile 1. First, clean the back of the pre-selected tiles and soak them for more than 2 hours. The purpose of soaking water is to let the tiles absorb moisture in advance, so as to avoid the moisture in the adhesive material after the plastering, affect the adhesive strength or cause excessive shrinkage of the adhesive material to cause hollowing, de-bonding, and the like. After the tile is immersed in water, it should be taken out from the water before being applied, and the surface moisture can be wiped off with a cotton cloth or the surface moisture can be dried before paving. 2. Before the paving begins, the vertical line should be hung on the wall leveling layer to determine the tile size line and pull the horizontal line so that the surface can be flat and the tile can be horizontal and vertical. Ensure that the base surface should be firm, smooth, clean, free of pollution, loose material, empty drums, etc. There are curing agents, mold release agents, and smoother concrete surfaces that need to be roughened and polished. 3. Add 25 kg of water to the craftsman's tile adhesive powder, approximately 7 to 7.5 kg, and stir the powder into a uniform, particle-free glue with an electric stirrer, and let it stand for 3 to 5 minutes before stirring. Bonding materials should not be too thick, otherwise it is not easy to spread, but also should not be too thin, otherwise tile paste can not be fixed, easy to fall down. 4. Squeeze the adhesive evenly onto the work surface with a tooth-type scraper, scrape about 1m2 each time, and then knead the tile on the work surface. 5, such as for the back of the ditch deeper tiles or stone, but also apply a tooth scraper on the back of the brick mortar, in order to ensure full paste. 6, according to the entire tile wall pollution situation, the surface can be scrubbed with water. How to buy tiles 1, look at the back of the brick, to see if the color is pure, generally pure color is shown as milky white (partially white), can not be black, can not be yellow, the surface is not a black spot, black hair yellow prove that the brick itself has impurities, The density of the bricks with more impurities will certainly decline, and it will be easily broken and damaged during normal use. However, the back of the brick is white and white and it is not normal. 2. See if the grain on the side of the tile is fine and uniform. If the grain is large and rough, the density of the brick body is crisp and loose. The use process will definitely cause problems. Take a simple example: when you get the house, it is usually a hair embryo house. The surface of the wall is very rough. When you use putty powder, the wall surface is smooth and delicate. You can use this standard to look just fine. 3, the brick up and hit the brick body by hand, the more crisp the sound proves that the higher the density of the brick body, the better the quality, the more boring sound proves that the tile density is worse, the worse the anti-fouling and durability of the tile. 4. If you buy polished tiles (over 600 size tiles), touch the front surface of the brick (hand touch), the smoother the surface feels, the less pinholes on the surface of the brick surface, the higher the dirt resistance. 5, the same color to see the gloss of the brick surface, the general floor tiles are placed on the sloping board, there will be above the spotlights or fluorescent lamps, you have to look at the shadow of these bulbs on the surface of the brick body (like looking in the mirror The same), the clearer the shadow, the higher the gloss of the brick, the stronger the hardness of the brick body, and the higher the durability performance. The darker the shadow of the light bulb, the lower the hardness of the brick. Note: I am referring to the polished tiles here, and the same color must be used when making comparisons. You cannot use yellow tiles and white tiles to compare. That is wrong. 6, if you buy antique tiles, then touch the front of the brick by hand, feel the brick surface glaze is delicate, and then watch with the eyes close, the glaze particles are rough and so on. Buy antique tiles must pay special attention to the quality of glaze, if possible, let the salesman explain in detail the production process of glaze, because the glaze is the life of the antique brick, and the color is the soul of the antique brick, so the color must be more Compare a few to see if the colors are pure, and pick a product with a relatively pure color that is basically OK. 7, if you buy porcelain tiles (wall tiles), then look at the brick body between the side of the body and the glaze to see the thickness of the glaze, too thin can not be, because a long time will appear broken or stained Happening. Look at the bright glaze on the surface of the tile. The glaze has good light quality. Editor's summary: The method of how to buy tiles and tiles is introduced here. I hope to help everyone. If you want to know more related information, you can pay attention to this website information. How tile tiles
Baking rack,baking cooling mesh,baking Cooling Rack,cooling rack, steel wire cooling rack, etc.
Baking wire mesh is made of high quality 304 stainless steel, never rusting and durable. Cooling Wire mesh does not have any coating or chemical ingredients, making food safer.
Cooling Rack,Barbecue Wire Mesh,Barbecue Mesh Grill,Bbq Mesh,Bbq Grill Metal Mesh Shenzhen Lanejoy Technology Co.,LTD , https://www.copper-nut.com
How to shop for tiles