The acceptance of solid wood flooring more inspector to teach you how to easily identify

The quality of the floor directly affects the quality of living and overall appearance of the house. Therefore, in the inspection process, the floor acceptance is an important link in the acceptance process of the fully furnished room. Fully-furnished room wooden floor "common diseases" mainly include: color, drum, deformation, there is a deviation of height and when walking stampede, as well as blinking, cracks, scratches and so on. Tongtai Home Inspector Studio Home Inspector Introduction: At present, the floor of the renovated room is more prominent.

Acceptance of solid wood flooring first depends on whether the floor color is the same. If the color difference is too large, directly affect the appearance, you can ask for exchange; if the color is too consistent, almost no color, it depends on the floor surface pattern is the same. If the pattern is almost the same, it may be craft wood floor, not the material floor of the so-called precious wood species. Some floor material suppliers nowadays use ordinary wood material flooring, but in the surface paste a layer of valuable wood veneer to shoddy, the reverse side with aluminum mooring stickers, said to be moisture-proof, in fact, is afraid to be seen The reverse pattern is inconsistent with the front.

The second step is to see whether the floor sounds, walk around on the floor during acceptance, the footsteps must be aggravated, especially the wall parts and door openings should pay more attention to acceptance, found that there are sound parts, to walk around to determine the specific location of the sound, Make a mark. In this case, you can ask to remove the resurfacing. The site where there are sounds is caused by non-standard operations and unqualified materials used by construction workers during the construction process. The operation is not standardized, mainly reflected in the fixed keel is not solid; material failure is mainly reflected in the ground keel without drying. Some renovation construction units use undried keel construction. The surface shows signs of drying. In fact, they did not dry. The regulations stipulate that the moisture content of decorative wood products should be controlled at about 12%. The keel with high moisture content will shrink in volume during the natural drying of the wood, causing looseness. Again, whether the flooring is deformed or warped, the acceptance method is to use a 2 meter long ruler, leaning against the floor, and the flatness should not exceed 3 mm. More than a few measurements, if the passing rate of 80% or more is considered qualified, and vice versa, is unqualified.

Sometimes we find that the floor is partially arched: if it is a solid wood floor, it is because it is too tight or the floor is too dry (water content is too low); if it is a laminate floor, it is a poor quality floor. Therefore, the arching of the floor is a serious quality problem.

Finally check the surface of the floor for defects such as blinks, crevices, and scratches. Commonly due to the untreated keel, there are locusts inside. When it was found that there was a blink, the floor was already almost cracked; gaps and scratches were known at a glance. The code stipulates that the gap in the floor should not be greater than 0.5 mm; the scratches are mainly caused by rough decoration, and if they cannot be repaired by waxing, they must be exchanged.

Nature floor del floor house space TV decoration home apartment decoration decoration style fashion small apartment decoration home

Polishing Buff Wheel

Bias Airway buffing wheel, also called as airway buffs, airflow buffs, Ventilated buffs. The special air folded structure brings bias airway buffing polishing wheel strong cutting force, high brightness, fine finishing, can cool the workpiece surface at a very short time. Make airway buffing polishing wheel widely use on metal and non metal products polishing, such as wood, stainless steel, aluminum, copper etc. Involved in variety of industries: furniture, automobile spare part, hardware, building materials,etc.

Airway buffs are a type of buffing and polishing wheel that is made up of multiple plys of cotton Cloth attached to a steel center plate. Each cloth layer of these 16-ply wheels is attached to the steel plate in a way that forces the cotton to form pleats.
High-speed buffing and polishing wheels can create a lot of heat from the constant friction of the wheel, surface being buffed, and Polishing Compound grinding at the same time. The fold are designed to increase airflow so that you can buff and polish at a lower temperature. This allows you to work continuously longer than traditional polishing wheels, extends the overall serving life of the airway buff, and lowers the chance of causing damage or burn to the object you are polishing.

The different colors of airway buffs are not there to let you work with your favorite color. Each of these colors has a different firmness/softness of the cloth pieces which are meant for different steps in the polishing process. You should also consider pairing each color buffing wheel with the appropriate color buffing compounds.

Cotton Polishing Buff Wheel,Sisal Buffing Wheel,Flap Buffing Wheel ,Non-woven Wheel Polishing

Jiangmen Gude Polishing Equipment Co., Ltd , https://www.kokipolishing.com