Cabinets are the most important piece of furniture in our kitchen. A small kitchen is basically occupied by cabinets. In general, the correct choice of cabinets is a common-sense problem that we must learn. When choosing a cabinet, not only the style and color are important, but also the issue of the size of the cabinet. We also need to pay attention to it. Let's take a look at the size of the cabinet . About the size of the cabinet design 1. The standard of the hanging cabinet does not include the standard depth of 300mm, the width is 200mm, 250mm, 300mm, 350mm, 400mm, etc. The hanging cabinet is too deep to affect the use. The standard height of the hanging cabinet is 650mm. In the small kitchen space, you can increase the hanging cabinet to get more storage space. The lower edge of the cabinet is generally 1500mm from the ground. Of course, there are European cabinet styles or visual effects. The bottom of the cabinet is only 450mm or even lower than the table top, depending on customer requirements and acceptance. 2, the floor cabinet standard does not include the door depth of 550mm, the width of 200mm, 250mm, 300mm, 350mm, 400mm, 450mm and other standard sequences, outside the standard cabinet hardware and electrical width. If the back of the cabinet is to avoid the pipeline, or the space is narrow, the cabinets with depths of 500mm, 450mm, 400mm, 350mm and 300mm can be made. The depth of the stove, sink and disinfection cabinet should not be less than 500mm. The standard height of the floor cabinet is 650mm, plus the kicking foot 110mm and the table top 40mm, the table top is just 800mm off the ground. If the customer has special requirements, the cabinet with height of 600mm, 720mm and 780mm can be made. According to ergonomics, the general cooktop is 250mm below the elbow, and the workbench is the most reasonable 150mm below the elbow. The cooking does not raise the hand, and the cut vegetables do not bend over. 3, the standard depth of the table top 595, if it is a hidden handle, the depth of the table is only 580mm, the table top is 50mm high and 10mm wide back water, no edge of the wall has a 40mm high front skirt, although the drawing does not need to draw The front skirt and the rear gear, but the design must be ignored. Sometimes to adapt to the disinfection cabinet and the cooktop, the front skirt can also be made to a height of 60mm. 4, the height of the bar should be based on the function, is the table or the bar, the table can be made equal to the table top, the bar is generally slightly higher than the table 100mm-150mm. Let's take a look at the measurement of cabinet size. 1. It is best to measure the length twice, from left to right and from right to left, so as not to look at the wrong size for the first time. 2. When measuring the height of the ceiling, it is necessary to measure the quasi-high points in several different directions, and at the same time, there are no beams under the gusset plate. 3, the measurement should look at the waist line, the bottom of the motorized socket to the height of the floor tile, and at the same time look at the height of the window (more attention should be paid when retesting). 4. When measuring, measure the distance and height of the gas meter and the pipeline from the wall, the height of the flue, the height of the inlet and outlet, the distance from the drainage supervisor to the wall, the height of the socket (retest), and so on. 5. When measuring, it is necessary to see whether there are steps on the ground, whether there are concave and convex beams on the wall, and when pulling the cabinet by the window, the pulling of the screen should be considered. If the cabinet is concerned, the relevant dimensions should be measured. 6. When the retest is done, the floor tiles should be paved and the wall tiles should be affixed. If the wall cabinet or the high cabinet is to the top, the roof should be hanged to retest. 7. When measuring the special shape or polygon, it is best to choose the fixed point and the diagonal of the quantity. When the two sides are made of the wall (the floor and the hanging cabinet), the inner and outer distances should be measured. 8. When there are poor bricks, it is necessary to measure the distance and height of the wall (including the height of the bottom and the top to the ground). The normal refrigerator position is preferably 700MM long, and the special additional length is reserved. 9. The thickness of the door cover should be measured and the thickness of the door cover (including the line), or the floor with the sliding door, the hanging cabinet should open the sliding door and leave a gap of 10-20MM. 10. When measuring the kitchen of the unit, pay attention to whether the wall is a stone wall or not, so that the wall cabinet cannot be installed. I believe that you should know how to choose the size of the cabinet now. In particular, the cabinet must not only have the function of storage but also be convenient in terms of use to realize its value. This is an important basis for our choice. If you want to know more about home improvement consultation, please continue to pay attention to the decoration home network. More related wonderful reading: What are the specifications of the cabinet size? What material cabinet size is adaptable? What factors determine the size of the cabinet? What are the sizes of plastic cabinets? How about blister cabinets? Cabinet size standard: enhance the new experience of the kitchen! Blind Box Toys Blind Box Toy Dongguan Maimeng Cultural Communication Co., LTD , https://www.icollectoys.com
Cabinet size design, cabinet size measurement problem