After many people have bought a house, they hope to transform or reinforce the house themselves. However, many people are not very clear about the reconstruction of the house and are still relatively unfamiliar. In fact, the transformation of the house is based on the original building to carry out a series of construction transformations, so as to reshape the original building. Then the most important issue in the reconstruction of a house is the reinforcement. How to reinforce it? The following professional renovation team will introduce you to the professional housing renovation and reinforcement methods. How to improve the housing reinforcement How to reconstruct a house is generally a combination of many methods. It is not a method that can be done. Strict words in the transformation and reinforcement of housing are calculated to be tolerant, and this average person does not. Therefore, the housing reform will be handed over to a professional house remodeling company, and there will be very few alterations of its own. If you reform yourself, pay more attention to the following methods. House reconstruction reinforcement method: The overall reinforcement is divided into two categories: one is direct reinforcement and the other is indirect reinforcement. Which is divided into many methods, Xiao Bian all to everyone listed below. 1. Strengthen the section reinforcement method: This method has simple construction process, strong adaptability, and mature design and construction experience; it can be used for concrete reinforcement of beams, slabs, columns, walls and structures; but the operation time is long, It has a certain impact on life or production, and the reinforced buildings have a certain impact on the headroom. 2, concrete reinforcement method: This method is similar to the advantages of the increase cross-section method, but does not affect the gap after the reinforcement structure, and there is no shortcomings of construction wet operation time; suitable for low-strength concrete or reinforced concrete bearing member beam, Columns are seriously flawed. 3, outsourcing sticking steel reinforcement method: This method is also known as the wet layer reinforcement method, the construction is simple, the workload is small, but the larger the amount of steel, should not be used in the unprotected place for high temperature above 600 °C The location; applies to the size does not allow significant increase in the original member section size, but requires greatly improved bearing capacity of reinforced concrete structures. 4. Paste steel plate reinforcement method: rapid construction, on-the-spot non-wet operation or gypsum wet method operation, which has little impact on production and life, and there is no obvious influence on the gap of the original original structure, but the reinforcement effect depends to a large extent Adhesive technology and operating level; suitable for bending and tensile members that withstand static and normal humidity environments or rebars. 5. Wire-winding method: The advantages and disadvantages of this method are similar to those of the enlarged cross-section method, and are not suitable for the bearing capacity of a reinforced concrete structure with an oblique cross-section, or where it is necessary to generate a combination of lateral pressure-receiving members. 6. Bolt Anchor Method: This method is applicable to the transformation and reinforcement of concrete bearing structures with concrete strength class C20 ~ C60; it is not applicable to the above structures and light structures with severe weathering. 7, rust-proof rust-proof reinforcement method: It is mainly used for corrosion of steel or new buildings under the conditions of use of the old building, prevent and prevent steel rust bulging structure technology. Housing reinforcement methods and characteristics 1. Reinforcement of carbon fiber composite materials: Continuous carbon fibers with high strength or high elastic modulus are bundled unidirectionally, and impregnated with epoxy resin to form a carbon fiber reinforced composite material sheet. The sheet is coated with a specially formulated epoxy resin. The structure is subjected to a ramen, and after the resin is solidified, a new force-complexed body is formed with the original structure, so that it is combined into a total force. Because the carbon fiber sheet shares the load, the stress of the steel bar is reduced, and the structure is strengthened and reinforced. 2. The carbon fiber reinforced material reinforcement method has many advantages such as convenient operation, quick construction, no wet work, small appearance influence, etc. It is widely used in industrial and civil buildings, bridge structures, tunnels, pipe culverts and other fields. 3, stick steel, steel reinforcement: the use of high-strength structural adhesive with good adhesion, the steel plate and the concrete structure firmly bonded together to form a composite overall structure, the effective transfer of stress to form an overall joint work, so as to restore or improve The bearing capacity of the structure and the strength and stiffness of the structure. It is suitable for the simple support and reinforcement of slabs and slabs due to insufficient capacity due to insufficient reinforcement. Compared with other similar reinforcement methods, the construction period is longer, but the increase in intensity is even greater. 4. Increase the cross-section reinforcement: It is often used in reinforcements or seismic reinforcements that require significant improvements in structure, member stiffness, and bearing capacity. The most obvious effect is to directly increase the stiffness and strength of the component. In some cases, the reinforcement of the cross-section of the member has unparalleled advantages over other reinforcement methods. Because of its outstanding effect, simple process, and low cost, it is widely used in the field of reinforcement and reconstruction engineering. 5. Analysis, treatment and repair of cracks: Structural cracks can be divided into two types, cracks caused by stress and cracks caused by deformation. For small deformation cracks, the method used is grouting: spread the adhesive evenly over the surface of the crack, allowing it to penetrate the crack root. When the crack is larger or is a force crack, a grout nozzle shall be arranged and the adhesive be driven into the root of the crack by means of pressure pouring. This technology is applicable to the repair of stable cracks in concrete structures and restores the integrity of the components to achieve the purpose of using functions. 6, chemical planting tendon technology: refers to the use of high-strength chemical adhesives, so that steel, screw and other concrete with a grip, the steel firmly anchored in the concrete. After the bar tending construction, the steel bar will have a high load bearing capacity, will not be easily displaced or pulled out, and has good sealing performance without any waterproof treatment. It will not only cause no expansion and damage to the substrate, but also has a reinforcing effect on the structure. . The construction is simple and rapid, safe and meets the requirements of environmental protection. It is the most effective method for changing, adding and reinforcing reinforced concrete structures in construction projects. The above points are the information on this site's Xiao Bian summarizing the reinforcement methods of professional housing for everyone. I believe we will have a certain understanding after reading it. In this way, everyone will know a lot, if you still have those who want to understand You can check it out on our website. House Decoration Designer Hengyang House Decoration Design Curtain Installation Method House Decoration Budget List House Decoration Precautions
Ningbo Actmix produces a group of environmental-friendly Rubber additives & chemicals. As special accelerator for EPDM and other synthetic rubber compound, does not contain any secondary amines which can form nitrosamines during vulcanization; and with excellent performance and dispersion. These chemicals included Actmix®Phosphorodithioic range, Actmix®CLD-80, Actmix®Retarder E-80, Actmix®TBzTD-70, Actmix®ZBEC-70 etc.
Actmix®Pre-dispersed rubber chemicals, impurity free, blocked filter free of extrusive products, scrap rate reduction and higher productivity thanks to filtration.Wider compatibility with other elastomers.
These chemicals are widely used for automotive rubber sealing system, sealing strip, rubber hose etc technical parts.
Environmental-friendly Rubber Chemical Environmental-friendly Rubber Chemical,Environmental-friendly Elastic Rubber,Environmental Life Casting Silicone Rubber,Environmental-friendly Rubber Getting Raw Oil Ningbo Actmix Rubber Chemicals Co., Ltd. , http://www.actmixchemicals.com
Professional house reconstruction and reinforcement methods guarantee safe life