7 bars led grow lights is a special lamp to provide light for plants. It usually consists of seven light bulbs, each with a different color and wavelength to simulate the spectrum of natural sunlight. This light fixture is widely used in indoor planting and gardening.
The use of the 7 bars full spectrum led grow lights mainly depends on the following aspects:
1. Light time: plants need light for photosynthesis, and different plants have different needs for light. In general, most plants need 10-12 hours of light per day, so 7 bars plant lights are usually set to work 10-12 hours per day.
2. Light intensity: Plants also have different needs for light intensity. Some plants require more light, while others require less light. 7 bars waterproof led grow lightss usually have an adjustable light intensity function that can be adjusted according to the needs of different plants.
3. Distance and Angle: The distance and Angle between the plant and the 7 bars indoor grow light will also affect the lighting effect. In general, the distance between the plant and the lamp should be kept within an appropriate range to ensure that the plant can fully receive the light.
4. Types of plants: Different plants have different needs for light. Some plants need stronger light to promote growth and flowering, while others have lower light requirements. Therefore, when using the 7 bars indoor grow lights veg, it needs to be adjusted according to the type and needs of the plant.
7 Bars Led Grow Light,Led Grow Lights For Indoor Plants,Plant Lamp,Indoor Plant Lights Shenzhen Pvison Technology Co., Ltd. , https://www.pvisunggrowlight.com
Cause Analysis and Improvement Measures of Serious Wear of Hydraulic Pump
Symptoms and causes analysis: In the maintenance of the following three points to find the cause of the malfunction, and the system to improve: (1) check the boom cylinder leakage situation. The easiest way is to raise the boom to see if there is a clear free fall. If the whereabouts of obvious removal of fuel tank inspection, seals have been worn should be replaced. (2) check the control valve. First clean the safety valve, check whether the spool wear, such as wear and tear should be replaced. If there is still no change after installation of safety valve, and then check the control valve spool wear, the gap limit of use is generally 0.06mm, severe wear and tear should be replaced. (3) measure the pressure of the hydraulic pump. If the pressure is low, then make adjustments, the pressure is still not adjustable, the serious damage to the hydraulic pump. 1. In general, the main reasons that the boom can not be lifted are as follows: a. The hydraulic pump is seriously worn. The pump leaks seriously at low speed. When the pump runs at high speed, the pump pressure slightly increases, but due to the wear and leakage of the pump, the volumetric efficiency drops significantly and it is difficult to reach the rated pressure. Hydraulic pump work for a long time has exacerbated the wear and tear, oil temperature, resulting in wear and tear of hydraulic components and seals aging, damage, loss of sealing ability, hydraulic oil deterioration, and finally lead to failure. b. hydraulic components selection is not reasonable. Boom cylinder specifications for 70/40 non-standard series, the seals are also non-standard parts, high manufacturing costs and seal replacement inconvenience. Boom cylinder bore is small, the system is bound to set high pressure. c. Hydraulic system design is not reasonable. As can be seen from Figure 1, the control valve and full hydraulic steering gear for a single pump in series, safety valve setting pressure points 16MPa, while the hydraulic pump rated working pressure is also 16MPa. Hydraulic pump often at full load or prolonged overload (high pressure) work, and the system has a hydraulic impact, long-term oil does not change, the hydraulic oil contaminated, exacerbating the hydraulic pump wear and tear, resulting in hydraulic pump shell burst (was found Such failure). Improvements and effects (l) Improve hydraulic system design. After several demonstrations, the final use of advanced priority valve and load sensing hydraulic steering gear form, the new system can follow the steering requirements, give priority to the distribution of traffic, regardless of the size of the load, the steering wheel speed can ensure adequate oil supply, the remaining part Can all be supplied to the working device circuit, thereby eliminating the power loss caused by excessive oil supply to the steering circuit, improving the system efficiency and reducing the working pressure of the hydraulic pump. (2) Optimize the design of boom cylinder and hydraulic pump to reduce the pressure of system work. Through optimization calculation, the boom cylinder adopts standard series 80/4. Hydraulic pump displacement increased from 10ml / r to 14ml / r, the system set pressure of 14MPa, to meet the boom cylinder lifting force and speed requirements. (3) Pay attention to proper use and maintenance of loaders in the process of using, regularly add or replace hydraulic oil, maintain the cleanliness of hydraulic oil, and strengthen routine inspection and maintenance.