In the decoration, the procedure of scraping putty is usually used. There is also an alias called brush wall paint. This is probably no stranger to everyone. Decorative wall putty is one way, mainly to scraping the wall putty to fill the place uneven surface, so that the wall is more flat and smooth. But when is the putty? How to scrape the putty ? Today, Xiaobian will take a look at the scraping wall putty skills and precautions! First, the method of scraping putty powder 1, shovel wall skin You can do a slight moisturizing test to check whether the original coating adhesion is acceptable. Most of the walls have been tested for a word: shovel! 2, the wall is closed 801 glue again The purpose is to enhance the bond between the putty and the wall. If you encounter an old house, you can increase the insurance factor by brushing the interface agent. 3. The negative angle handles the “elastic line†on both sides (note the verticality), and the positive angle can be handled by the lever. 4. Use gypsum powder and 801 glue to prepare all the plaster putty. In general, plaster lines are not recommended. 5, the wall leveling First check the wall for "empty drums" (can be tapped, listen to the sound), then use a slightly longer aluminum ruler to check the recesses on the top and wall, mark them, and level them with plaster putty. 6. After the official putty putty plaster putty is dried, apply putty (every time must be thoroughly dried). There are two ways to check whether the putty is dry: first, observe whether the color is consistent; then, when you look at the grinding, there is no "sticking sandpaper" phenomenon. 7, strong light oblique polishing, the top surface can be used 360 sandpaper. Tips for scraping wall putty: There is no skill in scraping putty, as long as we can carry out construction according to construction requirements and standards, but the following problems need to be noted. Of course, it can also be used as a putty skill to understand: 1, the ratio of water and putty powder 2, we scrape the putty for the first time, not asking for light but leveling. 3, the putty on the wall surface, generally requires three times to scrape, but each time the putty is required to dry it and then the next time to paint. When scraping the putty, be sure to avoid the cold wind blowing straight, so although it seems that the wall can be blown dry, in fact, it is to lock the moisture of the wall inside the wall, if you proceed to the next step Operation, when heating in the winter, the original wall material that has not dried will begin to evaporate and there will be a "dry crack". , Scrape wall putty tips - precautions for scraping putty 1. After the plaster putty is used up, the construction tools should be rinsed off with water in time. 2. The hardened gypsum putty can not be reused with water and stirring. 3. The bagged putty powder should be stored in a dry place, and there should be no moisture and agglomeration deterioration before use. 4, to adjust the putty powder to use clean water, water should not contain harmful substances such as sulfides. Finally, it is necessary to dispose of the uneven surface of the wall in time, and ensure that the putty fits closely with the wall. Of course, it is also important to choose a good decoration company to putty. The above is the short-sleeved putty tips and precautions that are introduced to you today. I want to know more information, please continue to pay attention to the decoration home. More related wonderful reading: Imitation porcelain putty construction process, the difference between imitation porcelain putty and scraping putty How much is the decoration of the putty wall? Precautions for decorating the putty wall How do the putty scrape fast and flat? Tips for scraping putty What brand of putty is used in the building interior? Putty construction guide How to make putty on the wall? Steps to put putty How to make putty on the wall? Process flow and construction points
Bathroom Sink faucet is heavily used every day between brushing your teeth and washing your hands multiple times. Choose a tub faucet that is not only reliable and water efficient, but also fits your style and budget. We have the latest styles of sink faucets to choose from. Stainless steel bathroom faucets are spot-proof. In addition to resisting spots and fingerprints, the matte black bathroom sink faucet enhances durability.
Bathroom Faucet,Sink Faucets,Shower Faucet JIANGMEN MEIAO KITCHEN AND BATH CO.,LTD , https://www.jmmeiao.com
What are the tips for scraping wall putty? Note on scraping wall putty