The kitchen faucet is a device that is often used in life. Its quality determines the service life of the faucet. And the kitchen faucet is directly related to the health of drinking water. If the faucet is not properly purchased, it will seriously threaten the safety of family members. Therefore, the following Xiaobian introduced how to choose the kitchen faucet. How to choose a kitchen faucet 1, to use smoothly: vegetables, steamed rice, soup, brush bowl ... ... annoying thing in the kitchen too much, it is best not to let the leading to add chaos! With a smooth faucet, often people do not feel it Existence, and this is mainly related to its spool, handle position, switch mode. A good tap valve can be easily opened and closed, and the handle will not be too loose or too tight when used. The position and shape of the handle should be easy to open and close. Even with the back of the hand, it can be easily operated. Traditional spiral and wrench type switches are no longer needed in the kitchen. Instead, a quick lift switch closes. 2, easy to clean: the kitchen will use the hands with grease, dirt to open the faucet, the faucet dirty. Therefore, it is best to choose a product that does not stain oil and facilitate scrubbing. This has a lot to do with the shape and plating of the faucet. Generally, faucets with complex shapes and changing lines tend to leave clean corners. The surface of the thin, low-hardness faucet is prone to rust, and the cleaning is not clean. The fence recommends that people still use a product that is simple in shape and hard-coated, which can save a lot of things. 3, the size is right: Some families of kitchen faucets easy to splash water, falling water can not reach the center of the sink ... ... This is ignored the sink, kitchen faucet with the. When choosing a kitchen faucet, be sure to know the sink size and choose the right faucet for this size. Make sure that the angle of the water outlet is right in the center of the sink. There can be a 180° or 360° rotation, and the distance from the bottom of the sink is hardly splashed. 4. Water saving and environmental protection: The consumption of water resources in the kitchen is very large, and the modern decoration “energy saving and environmental protection†is the mainstream. Therefore, it is necessary to pay attention to this point when selecting the tap. Water-saving faucets will save 30-40% of water compared to ordinary faucets, and they will save a lot of water bills when used. There are two main types of water-saving faucets. One is to use good bubblers to inject air into the water to prevent falling water from splashing and keep the flushing effect. At the same time, it slows the flow of water and reduces the flow of water to save water. The other is the handle "hint" design, when the handle is lifted to a certain height, there is a clear sense of stoppage, reminding the use of water has increased. 5, the style of unity: the unity of the decoration style is also more concerned about everyone, in the kitchen room, the sink can be used with different materials and styles, and the leader is mainly reflected in the online bar shape and surface coating. 6. User-friendly design: With the continuous improvement of kitchen faucet production technology, product design has become more humane. In addition to making it easy for everyone to use, the business also specializes in producing a left-handle faucet suitable for left-handed use. In addition, there are many different requirements for kitchen space, direct use of water for direct cleaning, like to use spray, enjoy the fun of innovation, etc., there are 360-degree rotating, pull-out nozzles, straight punch/spray head conversion, and flexible styling on the market. Variety of products. How to do leaking kitchen faucet 1. Leakage at the water outlet: The kitchen faucet is leaking. The water leakage at the outlet is caused by the abrasion of the shaft washer inside the faucet. Solution for water leakage at the outlet: Use a pair of pliers to loosen and remove the cover, remove the shaft washer with a clamp, and replace with a new shaft washer. 2. Leakage of the gap in the lower part of the faucet: The leakage of the gap in the lower part of the faucet is caused by the wear of the triangular gasket in the gland. Kitchen faucet leaking faucet 拴 lower gap leakage Solution: You can loosen the screw to remove the boring head, then loosen the cover, then remove the cover inside the triangle seal store, replace it with a new one. 3. Water leakage from the joint: Water leakage from the joint is generally caused by loosening of the cap nut. Solution for leaking water from the joint of the kitchen leak: At this point you can re-tighten the cap nut or replace with a new U-shaped gasket. Kitchen faucet cleaning tips 1, if it is a copper faucet, to clean the plating surface, you can use boiling water plus detergent scrub, you can also directly use some strong oil decontamination detergent to clean. 2, scales on the faucet, water rust, etc., just use a damp cloth or sponge, rub a few special cleaners to wipe the surface, then use a clean rag to dry or rinse with water. 3, use a soft toothbrush to remove the toothpaste or gently wipe with a scouring cloth to remove toothpaste, can remove scale, oil, so that the faucet surface is clean and bright. 4. Many people only pay attention to the surface of the faucet when cleaning the faucet, but in fact, the interior of the faucet is more important. If the amount of tap water is reduced or the water fork is produced, it may be due to a clogged bubbler. The bubbler can be removed and soaked in vinegar. Use a small brush or other Tool to clean the debris and reinstall it. Editor's summary: The introduction of how to choose a kitchen faucet is here, and I hope to help everyone. If you want to know more related information, you can pay attention to this website information. Faucet kitchen faucet
Taps and dies are tools used to create purpose screw threads, which is called threading. Many are cutting tools; others are forming tools. A tap is used to cut or form the female portion of the mating pair (e.g. a nut). A die is used to cut or form the male portion of the mating pair (e.g. a bolt). The process of cutting or forming threads using a tap is called tapping, whereas the process using a die is called threading. Drill And Tap Set,Hand Tap And Die,Cutting Tool Sets,Hand Tap Wrench Behappy Crafts (suzhou)Co.,Ltd , https://www.craftsbehappy.com
Using an ordinary tap or die to clean threads generally removes some material, which results in looser, weaker threads. Because of this, machinists generally clean threads with special taps and dies-called chasers-made for that purpose.
How to choose the kitchen faucet small details can not be ignored