It is not an easy task to install the washbasin in the bathroom. The washbasin is the basic part of the bathroom and is the most frequently used sanitary ware. Face wash, brushing, hand washing and some regular washing must use it, the bathroom should be decorated and practical, beautiful, is very critical to the treatment of the wash basin. Basin installation process Expansion bolts are inserted → æ» â†’ → → 盆 盆 盆 盆 盆 盆 挂 挂 挂 把 把 把 把 把 把 把 把 把 把 脸 脸 把 把 把 把 把 把 把 把 把 。 。 。 。 。 。 。 → Spatial decision format Washbasins are roughly divided into two types, freestanding and desktop. The stand-alone style is beautiful, the floor area is small, and it is easy to maintain. It is suitable for the bathroom with little space. However, it needs a mirror box or a washstand in order to use the space above the pool to place some toiletries and cosmetics. The tabletop sink should occupy at least a small desk space. Its countertops can be equipped with toiletries, and the following cupboards can also be used as miscellaneous items. If the bathroom area is not large, consider installing a triangular washbasin at the corner of the wall. Above the pool, you can hang a triangular rack to store detergent. Pay attention to height: Whether it is a free-standing or desktop washbasin, the height of the surface of the pool or table should be 80-85 cm, because a short pool can cause back pain. Pay attention to the degree of finish: The edge of the sink should be slightly higher than the top of the table, but it should be smooth when connecting with the table. The purpose is to wipe back the splashed water on the table without hindrance, and at the same time facilitate the cleaning of the table. The surface itself must be made of smooth material, and the edges and corners must be rounded to avoid bumping. The finish of the washbasin itself is also very important. The surface of the pool with high finish makes it difficult for the sundries in the water to adhere to the surface, and the number of scrubs is relatively reduced. Depth and Faucet: As a rule, the depth of the washbasin is directly proportional to the intensity of the faucet water flow installed on it, ie deep pools can be fitted with powerful taps. Don't install thick faucets on shallower sinks at the bottom. This can cause people to splash on water. The bottom of the pool should have enough curvature, not too flat, otherwise the water will accumulate in it. Basin installation construction essentials 1. Sink basin products should be flat and lossless. Drain plugs shall have overflow holes of not less than 8mm diameter. 2. Drain plugs and sinks should be arranged so that the drain plug overflow hole should be aligned with the overflow hole of the sink basin to ensure that the overflow site is clear. After the connection, the upper surface of the drain plug should be lower than the bottom of the wash basin. 3, bracket fixing bolts can be not less than 6mm galvanized bolts or galvanized metal expansion bolts such as the wall is a porous brick, it is strictly prohibited to use expansion bolts. 4. After connecting the sink with the drain pipe, it should be solid and compact, and it is easy to be disassembled, and the joint must not be exposed. The sinks are applied with silicone paste at the wall contact points. 5, such as wash basin drainage traps and taps are plated products, the installation must not damage the coating. Toilet basin installation: 1. Install the washbasin: Install a washstand with a pipe rack. Draw a vertical line in the middle of the drain nozzle. Measure the vertical height upward from the floor and draw a horizontal line on the wall. Draw a mark on the wall according to the width of the washbasin. , Hit holes 120 mm in diameter. Drain the bricks and other debris from the hole, insert the expansion bolts into the hole, and pry with the cement. The fine tubing should be hung up. Put the bolts on the rubber pads and eye sockets, and put on the nuts, and screw them to the appropriate pipe end. Head over the basin fixing hole. Place the washbasin on the rack to find a flat surface. Attach a 4 mm diameter bolt to a horizontal iron bar, insert the upper end into the mounting hole, and insert the lower end into the tube rack. Put on the nut and tighten until tight. 2. To install a cast iron basin, draw a vertical line at the center of the nozzle. Measure the vertical height from the floor, draw a horizontal line into a crosshair, and draw the mark on the horizontal line of the washbasin. Each vertical line was drawn and the pots were set up. The screw holes were placed in holes of 15 mm in diameter and 70 mm in length. The lead rolled into a roll and cut into a hole. Use the screws to fasten the basket to the wall. Place the washbasin on the rack, open the bolts of the movable frame, pull out the movable frame, and hook the rack on the washbasin hole. Inside, tighten the movable frame screws again, leveling and aligning. Tips: It wouldn't be easy to install beautiful and solid washbasins on the washbasin. There are some small details that I have to remind you about. Tip 1. In addition to the ordinary left in the socket near the basin, outside the basin under the cabinet to leave a small water heater installed later. Tip 2. Openings for the under counter basin are opened at the factory site. The on-site polishing takes time and results are poor. It should be noted that the position of the pre-opening hole must be accurate. The installation of the under counter basin is not a simple task. It must be a good workman. Post 3, the audience than the above counter basin basin Xiuqi, good-looking, good cleaning. With the basin mixer under the table should pay attention to, taking into account the thickness of the basin, the leading mouth to be longer. Stickers 4, toilet basin height should be moderate. Tips 5: The washbasin must be well-selected, and the drainage and water pipes should be arranged. Otherwise, it will be difficult to see if you need to pick up a lot of pipes. You must look at the sanitary ware to find someone who is knowledgeable, and some look good. Things may not be installed. Space effect figure entrance decoration space faucet socket cement cabinet bathroom washbasin En1092 Flange,En1092-1 Flange,Flange Type 01,Welding Neck Flanges Hebei Welkin Pipe Fitting Manufacturing Co., Ltd , https://www.welkinpipeline.com
Toilet basin installation essentials and acceptance
EN flange is a flange system from England, which have flange type including TYPE1(Plate Flanges); TYPE2(Losses Plate Flanges); TYPE5(Blank Flanges); TYPE11(Weld-neck Flanges); TYPE12(Hubbed Slip-on Flanges For Welding); TYPE13(Hubbed Threaded Flanges)etc., pressure grade have PN2.5 PN6 PN10 PN16 PN25 PN40 PN63 PN100, Size from 1/2" NB TO 48"NB